Portsdown Sweeper - Revision history

G8GKQ at 17:48, 14 May 2024

2024-05-14T17:48:28Z

G8GKQ: /* Making a Measurement */

2021-11-20T19:43:58Z

Making a Measurement

G8GKQ at 15:13, 20 November 2021

2021-11-20T15:13:48Z

G8GKQ at 14:52, 20 November 2021

2021-11-20T14:52:12Z

G8GKQ: Created page with "The Portsdown 4 includes a Frequency Sweeper (STILL UNDER DEVELOPMENT) that uses the LimeSDR Mini and an RF Power Sensor to provide an indication of the frequency response of..."

2021-11-20T13:23:35Z

Created page with "The Portsdown 4 includes a Frequency Sweeper (STILL UNDER DEVELOPMENT) that uses the LimeSDR Mini and an RF Power Sensor to provide an indication of the frequency response of..."

New page

The Portsdown 4 includes a Frequency Sweeper (STILL UNDER DEVELOPMENT) that uses the LimeSDR Mini and an RF Power Sensor to provide an indication of the frequency response of filters and amplifiers. It is hoped to describe this emerging capability in CQ-TV 274 (Winter 2021). This Wiki page is purely to inform the early beta testers before the capability goes on general release.

@@ Line 1: / Line 1: @@
-The Portsdown 4 includes a Frequency Sweeper (STILL UNDER DEVELOPMENT) that uses the LimeSDR Mini and an RF Power Sensor to provide an indication of the frequency response of filters and amplifiers. It is hoped to describe this emerging capability in CQ-TV 274 (Winter 2021). This Wiki page is purely to inform the early beta testers before the capability goes on general release.
+Both the Portsdown 4 and Portsdown 2020 include a Frequency Sweeper that uses the LimeSDR Mini and an RF Power Sensor to provide an indication of the frequency response of filters and amplifiers.
 ===General Principle===
@@ Line 9: / Line 9: @@
 [[File:Sweeper Block Diagram.jpg|960px]]
-The sweeper requires a Portsdown 4 (not a Portsdown 2020, yet), a LimeSDR Mini and the power meter sensor that was described in CQ-TV 273.  The ciruit of the power meter head is very simple:
+The sweeper requires a Portsdown, a LimeSDR Mini and the power meter sensor that was described in CQ-TV 273.  The ciruit of the power meter head is very simple:
 [[File:4 Circuit.PNG|978px]]
 ===Making a Measurement===
-Connect the system up as shown above.  Note that the LimeSDR will produce a calibration pulse of 50 mW, so it is recommended that 5-10 dB attenuators are used on the input and output of the device to protect the device and power head, and also to minimise the effect of cable reflections.
+Connect the system up as shown above.  Note that the LimeSDR will produce a calibration pulse of up to 50 mW, so it is recommended that 5-10 dB attenuators are used on the input and output of the device to protect the device and power head, and also to minimise the effect of cable reflections.
 Select the Sweeper from Menu 2, Test Equipment.  The sweeper will calibrate the LimeSDR and run straight away.  You can change the centre frequency and the frequency span from the Set-up Menu.

@@ Line 18: / Line 18: @@
 Select the Sweeper from Menu 2, Test Equipment.  The sweeper will calibrate the LimeSDR and run straight away.  You can change the centre frequency and the frequency span from the Set-up Menu.
-Because the LimeSDR Mini takes a finite time to move to each frequency, plotting with many points is slow, and difficult to use for real-time alignment.  The number of sample points can be reduced to allow fast coarse alignement of circuits and filters.  The output level of the LimeSDR can also be adjusted.
+[[File:sweeper.jpg|800px]]
 The Marker menu allows the measurement of peak, null or manually-chosen levels.
@@ Line 24: / Line 24: @@
 Normalisation can be used to set the sweeper to display a flat response without the device under test in circuit, and then the device can be connected to show its response without any effect from the measuring setup.
-[[File:sweeper.jpg|800px]]
+===Limitations===

@@ Line 1: / Line 1: @@
 The Portsdown 4 includes a Frequency Sweeper (STILL UNDER DEVELOPMENT) that uses the LimeSDR Mini and an RF Power Sensor to provide an indication of the frequency response of filters and amplifiers. It is hoped to describe this emerging capability in CQ-TV 274 (Winter 2021). This Wiki page is purely to inform the early beta testers before the capability goes on general release.
 ===Equipment Required===
 [[File:Sweeper Block Diagram.jpg|960px]]

← Older revision		Revision as of 14:52, 20 November 2021
Line 1:		Line 1:
	The Portsdown 4 includes a Frequency Sweeper (STILL UNDER DEVELOPMENT) that uses the LimeSDR Mini and an RF Power Sensor to provide an indication of the frequency response of filters and amplifiers. It is hoped to describe this emerging capability in CQ-TV 274 (Winter 2021). This Wiki page is purely to inform the early beta testers before the capability goes on general release.		The Portsdown 4 includes a Frequency Sweeper (STILL UNDER DEVELOPMENT) that uses the LimeSDR Mini and an RF Power Sensor to provide an indication of the frequency response of filters and amplifiers. It is hoped to describe this emerging capability in CQ-TV 274 (Winter 2021). This Wiki page is purely to inform the early beta testers before the capability goes on general release.
		+
		+	===Equipment Required===
		+
		+	[[File:Sweeper Block Diagram.jpg\|960px]]