Difference between revisions of "Initial setup 2019"

From BATC Wiki
Jump to navigation Jump to search
(Created page with "'''Important note - the Portsdown transmitter has been designed to "work out of the box". Most things can be set-up from the touchscreen. A few more advanced functions requi...")
 
 
(11 intermediate revisions by 2 users not shown)
Line 1: Line 1:
 
'''Important note - the Portsdown transmitter has been designed to "work out of the box".  Most things can be set-up from the touchscreen.  A few more advanced functions require you to connect to your Portsdown over a network from a PC.
 
'''Important note - the Portsdown transmitter has been designed to "work out of the box".  Most things can be set-up from the touchscreen.  A few more advanced functions require you to connect to your Portsdown over a network from a PC.
  
Note that if you have a 7 inch Touchscreen, you should start at "Set-up using a PC"
+
Note that if you have a 7 inch Touchscreen, you should start at "Set-up using a PC".  You can then reboot and use your touchscreen.
  
 
*'''Do not''' connect a mouse, keyboard or monitor to the Raspberry Pi
 
*'''Do not''' connect a mouse, keyboard or monitor to the Raspberry Pi
Line 10: Line 10:
 
-------------------------
 
-------------------------
  
===Set Up through the 3.5 inch Touchscreen===
+
If you do not have a waveshare screen or you wish to enter the system advanced set-up pages you will need to follow this initial setup procedure.
  
Once you have a RPi and an SD card with the Portsdown firmware installed - either from the BATC shop or by following [[Portsdown software|the instructions in this section of the user guide]] connect the Waveshare 3.5 inch touchscreen (being careful to align the pins correctly)
+
===Find the Rpi IP address===
 +
 
 +
If you have a 3.5 inch touchscreen but want to adjust the advanced settings, you can look up your IP address from the info screen on Menu 2.
 +
 
 +
If you have no working touchscreen (for example a 7 inch screen at Initial Setup), you will need to run an IP Scanner program on your PC to find your Rpi address.  Download it from [http://www.advanced-ip-scanner.com/ Advanced IP Scanner] and scan for devices; after a few seconds it will list all the devices on your network including one from the Raspberry Pi foundation - this is your RPi so note down the IP address listed against it.  You can now close the IP scanner program.
 +
 
 +
'''Running the setup menu'''
 +
 
 +
Now you need to log on to your RPi using a PC over your home network (DO NOT connect a keyboard and monitor directly to the RPi).  To do this you need to download an SSH Terminal application such as [http://www.chiark.greenend.org.uk/~sgtatham/putty/ Putty] to edit the set up menu - make sure you use a recent version of putty or it may reject the RPi security certificate.
 +
 
 +
*Open Putty or another SSH terminal program, enter the IP address of your RPi and open a connection.  The first time that you do this, you will get a security warning; accept it.  At the logon prompt enter the default username of "pi" and the password "raspberry".
 +
 
 +
*The Portsdown console menu will start automatically, and you should see the following screen on the PC:
 +
 
 +
[[File:1-2 Main Menu.jpg|661px]]
 +
 
 +
===Choosing your display mode===
 +
 
 +
The first thing that you should select is the correct display option. Use the arrow keys to highlight Option 5 System Setup and then press enter.  Then highlight Display Type and press enter.  Lastly, use the arrow keys to move the cursor to your display, and press the space bar to select it.  Then press enter.
 +
 
 +
If you do not want to select any more advanced options, you can now highlight Option 8 Shutdown then press enter, and then highlight Reboot Now and press enter.  Your selected display should work after a Portsdown system reboot.
 +
 
 +
You need to use the console menu to select the following functions
 +
 
 +
* Autostart.  This sets what happens when the Portsdown starts up.
 +
* WiFi
 +
* Display type as described above
 +
* Enable/disable hardware shutdown button
 +
* Restore the touch calibration to factory defaults
 +
* Set up the Portsdown to continuously stream to the BATC Server (for a repeater)

Latest revision as of 18:08, 4 February 2019

Important note - the Portsdown transmitter has been designed to "work out of the box". Most things can be set-up from the touchscreen. A few more advanced functions require you to connect to your Portsdown over a network from a PC.

Note that if you have a 7 inch Touchscreen, you should start at "Set-up using a PC". You can then reboot and use your touchscreen.

  • Do not connect a mouse, keyboard or monitor to the Raspberry Pi
  • Do not load any device drivers including the Waveshare screen drivers
  • Do not tinker with Linux commands

If you do, we don't have time to support you and will just advise you to reformat your SD card and start again!


If you do not have a waveshare screen or you wish to enter the system advanced set-up pages you will need to follow this initial setup procedure.

Find the Rpi IP address

If you have a 3.5 inch touchscreen but want to adjust the advanced settings, you can look up your IP address from the info screen on Menu 2.

If you have no working touchscreen (for example a 7 inch screen at Initial Setup), you will need to run an IP Scanner program on your PC to find your Rpi address. Download it from Advanced IP Scanner and scan for devices; after a few seconds it will list all the devices on your network including one from the Raspberry Pi foundation - this is your RPi so note down the IP address listed against it. You can now close the IP scanner program.

Running the setup menu

Now you need to log on to your RPi using a PC over your home network (DO NOT connect a keyboard and monitor directly to the RPi). To do this you need to download an SSH Terminal application such as Putty to edit the set up menu - make sure you use a recent version of putty or it may reject the RPi security certificate.

  • Open Putty or another SSH terminal program, enter the IP address of your RPi and open a connection. The first time that you do this, you will get a security warning; accept it. At the logon prompt enter the default username of "pi" and the password "raspberry".
  • The Portsdown console menu will start automatically, and you should see the following screen on the PC:

1-2 Main Menu.jpg

Choosing your display mode

The first thing that you should select is the correct display option. Use the arrow keys to highlight Option 5 System Setup and then press enter. Then highlight Display Type and press enter. Lastly, use the arrow keys to move the cursor to your display, and press the space bar to select it. Then press enter.

If you do not want to select any more advanced options, you can now highlight Option 8 Shutdown then press enter, and then highlight Reboot Now and press enter. Your selected display should work after a Portsdown system reboot.

You need to use the console menu to select the following functions

  • Autostart. This sets what happens when the Portsdown starts up.
  • WiFi
  • Display type as described above
  • Enable/disable hardware shutdown button
  • Restore the touch calibration to factory defaults
  • Set up the Portsdown to continuously stream to the BATC Server (for a repeater)