Difference between revisions of "Using LimeSDR with Portsdown"

From BATC Wiki
Jump to navigation Jump to search
 
(10 intermediate revisions by 3 users not shown)
Line 1: Line 1:
 
===Introduction===
 
===Introduction===
  
The Portsdown 2019 software supports the LimeSDR Mini and the LimeSDR USB.   
+
The Portsdown software supports the LimeSDR Mini.  Support for the LimeSDR USB is provided on a best-efforts basis, but not tested.   
  
With the Portsdown Filter Modulator board being discontinued, the LimeSDR Mini will become the standard modulator for use with the Portsdown system and is available for purchase in the BATC members shop.  More details on the LimeSDR Mini can be found here [[LimeSDR Mini Information]].
+
However, due to the limited CPU power of the Raspberry Pi, many LimeSDR transmit modes are limited to 1MS and below.
 
 
The LimeSDR Mini is slightly more expensive than the Portsdown Filter Modulator board but does not require the use of a separate ADF4351 Local Oscillator module and a Local Oscillator filter board.  Note - the LimeSDR Mini is available from the BATC members shop at a slightly discounted price compared to the normal retail price from the US plus shipping and 22% import duty charges.
 
 
 
However, due to the limited CPU power of the Raspberry Pi, many LimeSDR transmit modes are limited to 1MS and below.  For higher SRs, use of the Portsdown Filter-modulator board is recommended. (see limitations below).
 
  
 
===Setting up the system===
 
===Setting up the system===
Line 14: Line 10:
  
 
===Hardware Installation===
 
===Hardware Installation===
Whilst the LimeSDR could be plugged directly in to the RPi, both the Mini and the USB versions have a greater power consumption than the RPi can comfortably power from its USB Port.  Therefore, it is recommended that a powered USB 2 Hub be connected to the RPi, and the LimeSDR be plugged into one of the ports on the hub.  Note that some narrow-band applications of the LimeSDR might require USB 3, but USB 3 ports have enough power to supply a LimeSDR Mini, so do not require a hub.
+
If you are using a Rapsberry Pi 3, both the LimeSDR Mini and USB versions have a greater power consumption than the RPi can comfortably power from its USB 2 ports.  Therefore, it is recommended that a powered USB 2 hub be connected to the RPi, and the LimeSDR be plugged into one of the ports on the hub.   
 +
 
 +
If you are using a Raspberry Pi 4, its USB ports have enough power to supply a LimeSDR Mini or USB, so a hub is not required.  For some reason, the LimeSDR Mini sometimes works better when connected to the USB2 ports (the black ones, not the Blue ones).
  
 
The USB plug on the LimeSDR Mini is vulnerable to mechanical stress; it is recommended that the LimeSDR Mini (or LimeSDR USB) be mounted in a protective box with strain relief for a USB lead.  One possible mechanical configuration is illustrated below.  There are number of 3D printed cases which can be used to protect the unit [https://forum.batc.org.uk/viewtopic.php?t=5813&p=17948#p17919 see the thread on the members forum] for more details.
 
The USB plug on the LimeSDR Mini is vulnerable to mechanical stress; it is recommended that the LimeSDR Mini (or LimeSDR USB) be mounted in a protective box with strain relief for a USB lead.  One possible mechanical configuration is illustrated below.  There are number of 3D printed cases which can be used to protect the unit [https://forum.batc.org.uk/viewtopic.php?t=5813&p=17948#p17919 see the thread on the members forum] for more details.
Line 20: Line 18:
 
Charles, G4GUO, has found the LimeSDR Mini fits in to a Hammond 1455C802 box - see http://g4guo.blogspot.com/2018/05/my-lime-mini-has-box.html for more details but the USB connector may still need additional support.
 
Charles, G4GUO, has found the LimeSDR Mini fits in to a Hammond 1455C802 box - see http://g4guo.blogspot.com/2018/05/my-lime-mini-has-box.html for more details but the USB connector may still need additional support.
  
The BATC 8-band PTT drive and RF switching boards can be used with the Lime to provide band switching - see below for details on the GPIO port connections.
+
The BATC 4-band and 8-band PTT drive and RF switching boards can be used with the Lime to provide band switching - see below for details on the GPIO port connections.  When using the 8-band switch, make sure to use the latest version with the attenuating resistors between the MMIC and the switch ICs.
  
 
===Installing the Lime Software===
 
===Installing the Lime Software===
  
The LimeSuite software version 19.01.0 (Interface version v2019.1.0, Binary Interface 19.01-1) is loaded as part of the normal Portsdown build and update process.  This may not be the latest version, but is compatible with other components of the Portsdown software and the latest DATV Express version.
+
The LimeSuite software version 20.10.0 (Interface version v2021.10.0, Binary Interface 20.10-1) is loaded as part of the normal Portsdown build and update process.  This may not be the latest version, but is compatible with other components of the Portsdown software and the latest DATV Express version.
  
Once installed, you can use your Portsdown to update the firmware and gateware on your LimeSDR (Mini or USB) to the compatible version, but you must be connected to the internet whilst upgrading.  If you have attempted to upgrade a LimeSDR while not connected to the internet, you need to delete the 0 byte file that will have been created before you can successfully upgrade.  The "Del Lime FW on RPi" button on the Lime Configuration menu does this.
+
Once installed, you can use your Portsdown to update the firmware and gateware on your LimeSDR (Mini or USB) to the compatible version, but you must be connected to the internet whilst upgrading a LimeSDR USBThe firmware to upgrade a LimeSDR Mini is stored on the Portsdown as part of the Portsdown build process.
  
 
===Lime Configuration Menu===
 
===Lime Configuration Menu===
Line 32: Line 30:
 
The "Lime Config" Menu is selected from Menu 3.  Selecting "LimeUtil Info" displays the current version of LimeSuite.
 
The "Lime Config" Menu is selected from Menu 3.  Selecting "LimeUtil Info" displays the current version of LimeSuite.
  
The "Update Lime FW" button updates the Lime SDR firmware and gateware to the appropriate version for the installed LimeSuite.  For Portsdown software versions 201903250 and later, the correct version is shown below.  You should see the same screen after selecting "Lime FW Info".
+
The "Update Lime FW" button updates the Lime SDR firmware and gateware to the appropriate version for the installed LimeSuite.  For recent Portsdown software versions, the correct version is shown below.  You should see the same screen after selecting "Lime FW Info".
  
[[File:lime129.jpg|400px]]
+
[[File:Lime130.jpg|400px]]
  
 
The Lime firmware/gateware version that works with the Portsdown is also compatible with DATV Express versions V1.25lp12 and later.
 
The Lime firmware/gateware version that works with the Portsdown is also compatible with DATV Express versions V1.25lp12 and later.
  
===BATC Shop LimeSDR Minis===
+
===Using a LimeSDR USB===
 
 
The LimeSDR Minis purchased from the BATC shop are hardware version 1.2.  Those purchased before 14 January 2019 will have firmware 1.26 loaded.  Those purchased after 14 January 2019 will have the latest firmware at the time of sale loaded.
 
 
 
If you do not use the correct firmware, the transmitted spectrum will not be as clean.  If you are unable to upgrade due to apparent problems with the Portsdown/LimeSDR combination, please report the details on the BATC forum.
 
  
Note that if you use a Windows PC or a different Linux build to upgrade the firmware to beyond 1.29, you can roll it back to the correct version for the Portsdown by selecting "Force Lime FW" on the touchscreen menu.
+
You can also use the more expensive LimeSDR USB (as opposed to the LimeSDR Mini) with the Portsdown. You can update the gateware and firmware to the correct version (Firmware Version 4, Gateware version 2.20), but the Lime Report will fail as it is designed for the LimeSDR Mini.  The Portsdown should operate normally with a LimeSDR USB, although this is not a configuration that is tested before the release of software updates.
  
 
===Basic Test===
 
===Basic Test===
  
You can run a basic test on your LimeSDR Mini, by pressing the "Lime Report" button.  Note that this test generates RF output and leaves the LimeSDR Mini generating a carrier on 1095 MHz at about -25 dBm.
+
You can run a basic test on your LimeSDR Mini, by pressing the "Lime Report" button.  Note that this test generates RF output and leaves the LimeSDR Mini generating a carrier on 1095 MHz at about -25 dBm.  This test rarely passes unless the LimeSDR Mini is cold and the RF ports are disconnected.  A functional test (transmitting, or receiving using BandViewer) is a better indication of LimeSDR Mini health.
  
 
==='''WARNING - High Power Output During Calibration Before Transmit'''===
 
==='''WARNING - High Power Output During Calibration Before Transmit'''===

Latest revision as of 09:06, 20 October 2021

Introduction

The Portsdown software supports the LimeSDR Mini. Support for the LimeSDR USB is provided on a best-efforts basis, but not tested.

However, due to the limited CPU power of the Raspberry Pi, many LimeSDR transmit modes are limited to 1MS and below.

Setting up the system

Either buy a pre-configured SD card from the BATC shop https://batc.org.uk/category/portsdown/ or download and install the standard Portsdown software on your own SD card - see this page for more details: https://wiki.batc.org.uk/Initial_setup

Hardware Installation

If you are using a Rapsberry Pi 3, both the LimeSDR Mini and USB versions have a greater power consumption than the RPi can comfortably power from its USB 2 ports. Therefore, it is recommended that a powered USB 2 hub be connected to the RPi, and the LimeSDR be plugged into one of the ports on the hub.

If you are using a Raspberry Pi 4, its USB ports have enough power to supply a LimeSDR Mini or USB, so a hub is not required. For some reason, the LimeSDR Mini sometimes works better when connected to the USB2 ports (the black ones, not the Blue ones).

The USB plug on the LimeSDR Mini is vulnerable to mechanical stress; it is recommended that the LimeSDR Mini (or LimeSDR USB) be mounted in a protective box with strain relief for a USB lead. One possible mechanical configuration is illustrated below. There are number of 3D printed cases which can be used to protect the unit see the thread on the members forum for more details.

Charles, G4GUO, has found the LimeSDR Mini fits in to a Hammond 1455C802 box - see http://g4guo.blogspot.com/2018/05/my-lime-mini-has-box.html for more details but the USB connector may still need additional support.

The BATC 4-band and 8-band PTT drive and RF switching boards can be used with the Lime to provide band switching - see below for details on the GPIO port connections. When using the 8-band switch, make sure to use the latest version with the attenuating resistors between the MMIC and the switch ICs.

Installing the Lime Software

The LimeSuite software version 20.10.0 (Interface version v2021.10.0, Binary Interface 20.10-1) is loaded as part of the normal Portsdown build and update process. This may not be the latest version, but is compatible with other components of the Portsdown software and the latest DATV Express version.

Once installed, you can use your Portsdown to update the firmware and gateware on your LimeSDR (Mini or USB) to the compatible version, but you must be connected to the internet whilst upgrading a LimeSDR USB. The firmware to upgrade a LimeSDR Mini is stored on the Portsdown as part of the Portsdown build process.

Lime Configuration Menu

The "Lime Config" Menu is selected from Menu 3. Selecting "LimeUtil Info" displays the current version of LimeSuite.

The "Update Lime FW" button updates the Lime SDR firmware and gateware to the appropriate version for the installed LimeSuite. For recent Portsdown software versions, the correct version is shown below. You should see the same screen after selecting "Lime FW Info".

Lime130.jpg

The Lime firmware/gateware version that works with the Portsdown is also compatible with DATV Express versions V1.25lp12 and later.

Using a LimeSDR USB

You can also use the more expensive LimeSDR USB (as opposed to the LimeSDR Mini) with the Portsdown. You can update the gateware and firmware to the correct version (Firmware Version 4, Gateware version 2.20), but the Lime Report will fail as it is designed for the LimeSDR Mini. The Portsdown should operate normally with a LimeSDR USB, although this is not a configuration that is tested before the release of software updates.

Basic Test

You can run a basic test on your LimeSDR Mini, by pressing the "Lime Report" button. Note that this test generates RF output and leaves the LimeSDR Mini generating a carrier on 1095 MHz at about -25 dBm. This test rarely passes unless the LimeSDR Mini is cold and the RF ports are disconnected. A functional test (transmitting, or receiving using BandViewer) is a better indication of LimeSDR Mini health.

WARNING - High Power Output During Calibration Before Transmit

When the LimeSDR is put into transmit mode, it first performs a self-calibration which transmits at high power both in-band and out-of-band. It is imperative that power amplifiers are not energised during this phase or they will be damaged and/or strong illegal transmissions will be made out-of-band.

First power tests with Lime Mini SDR Portsdown at M0YDH

There are 2 delayed PTT signals available to help you avoid this situation. The first is on the normal Portsdown PTT pin on the RPi. The second is on GPIO 7 on the LimeSDR Mini or Lime SDR USB. None of these signals go high until calibration is finished.

Transmitting

Select Lime Mini or Lime USB from the "Output to" Menu. The detected device should be "not greyed out". On Menu 1, you will see the Lime Gain button for the appropriate band (distinct Lime Gains between 0 and 100 are stored for each band). A setting of 88 is a good starting point for about 5 dBm of output at 437 MHz. More information about the LimeSDR Mini output power levels and controls can be found here LimeSDR Mini Output Power Levels.

Selecting the modulation button will allow you to choose between Carrier, DVB-S and DVB-S2 modes. Once a DVB-S2 mode is selected, the appropriate FECs are available on the FEC button. Note that different FECs are available (and not available) for different modulations.

The RPi has to work quite hard to generate the signals to drive the LimeSDR. All SRs at 1MS and below seem to be reliable, but SRs of 2MS and 4MS can suffer drop-outs, particularly in MPEG-2 transmission modes. For operation above 1MS, the Portsdown Filter-Modulator board is recommended, rather than the LimeSDR.

Limitations

There are 3 transmission modes used by the LimeSDR with Portsdown: SDR without up-sampling, SDR with 2 x up-sampling and carrier mode. I have tried to level the powers across these 3 modes, but they will vary by 2 or 3 dB depending on the SR and Lime gain selected.

There is a failure mode where the LimeSDR refuses to transmit anything other than a carrier, or does not respond at all. It has not been possible to overcome these failures yet in software; the solution is to power down the LimeSDR (by disconnecting the power and USB leads), and then to reconnect them.

GPIO RF Switching for Multiple Bands

The BATC 4-band and 8-band PTT drive and RF switching boards can be used with the LimeSDR to provide multiband RF and PTT steering. They can remain connected to the RPi GPIO using the standard Portsdown GPIO interface board or (if you are prepared to accept the risk of damaging your LimeSDR Mini) connected to the Lime FPGA GPIO.

The LimeSDR Mini GPIOs 0, 1 and 2 give the same signals as the RPi Band LSB, NSB and MSB. GPIO 7 gives the PTT signal. These can be taken from J5 on the LimeSDR Mini https://wiki.myriadrf.org/LimeSDR-Mini_v1.1_hardware_description . For the LimeSDR USB, the GPIO signals are available on J18; the PTT signal is reported to be on FPGA-GPIO 5 (pin 8 in header), but this has not been investigated.

The pins are described here http://wiki.myriadrf.org/LimeSDR-USB_hardware_description.  Note that these outputs are not buffered and if damaged could prevent the LimeSDR from working again.  Our advice is the use the RPi GPIOs.

GPIO Test.jpg

The gain provided by the 8-way RF switch is useful to maintain current levels (5 - 10 mW) at the output. To ensure the correct output levels are available, C16 (2p7) needs reducing to 1pf, and R5 (68 ohms) needs replacing with a wire link. Alternatively R5 could be simply be replaced with a 2p2 or 1p8 capacitor and C16 left as 2p7.

On the Lime USB the output is from "TX1 Low" below 2 GHz and from "TX1 High" above 2 GHz. The Lime Mini only has a single output.

System Diagram

Here is the latest system diagram. Note that only one of the displays is required; either the 3.5 inch or 7 inch.

20190120 Portsdown 2019 Block.jpg

The digital variable attenuator is only required if you want fine (<3 dB steps) control over your PA drive levels. The Lime Gain control on the Portsdown can be used to set the coarse output level.

Acknowledgements

Thanks to Evariste F5OEO, Andrew Back at Myriad RF, Charles G4GUO and Malcolm G0UHY for their help in implementing this capability.