Difference between revisions of "Initial setup"

From BATC Wiki
Jump to navigation Jump to search
Line 1: Line 1:
 
===Initial set up===
 
===Initial set up===
Once you have built the Hardware and got an SD card with the firmware from either the BATC shop or by following [[Portsdown software|these instructions]], the system must be setup using an external PC running 2 pieces of software - the first application is to find the IP address of your RPi when it first boots up, such as [http://www.advanced-ip-scanner.com/ Advanced IP Scanner] and an SSH Terminal application such as [http://www.chiark.greenend.org.uk/~sgtatham/putty/ Putty].   
+
Once you have an SD card with the Portsdown firmware installed - either from the BATC shop or by following [[Portsdown software|these instructions]] - the system must be setup using an external PC running 2 pieces of software - the first application is to find the IP address of your RPi when it first boots up, such as [http://www.advanced-ip-scanner.com/ Advanced IP Scanner] and an SSH Terminal application such as [http://www.chiark.greenend.org.uk/~sgtatham/putty/ Putty].   
  
 
*Using a network lead (not wifi at this stage), connect the RPi to the same network as your PC, install the SD card and turn the Rpi on (you do not need a keyboard, mouse or monitor connected to the Rpi).  After it has booted up, use the IP Scanner to find the IP address of your RPi.
 
*Using a network lead (not wifi at this stage), connect the RPi to the same network as your PC, install the SD card and turn the Rpi on (you do not need a keyboard, mouse or monitor connected to the Rpi).  After it has booted up, use the IP Scanner to find the IP address of your RPi.

Revision as of 20:10, 3 January 2017

Initial set up

Once you have an SD card with the Portsdown firmware installed - either from the BATC shop or by following these instructions - the system must be setup using an external PC running 2 pieces of software - the first application is to find the IP address of your RPi when it first boots up, such as Advanced IP Scanner and an SSH Terminal application such as Putty.

  • Using a network lead (not wifi at this stage), connect the RPi to the same network as your PC, install the SD card and turn the Rpi on (you do not need a keyboard, mouse or monitor connected to the Rpi). After it has booted up, use the IP Scanner to find the IP address of your RPi.
  • Open Putty and enter the IP address of your RPi and open a connection. At the logon prompt enter the default username of pi and the password given to you with the card. The console menu will start automatically and you will see the following screen:

Note - in all menus press the up and down PC keyboard arrows to highlight the item that you require and then the space bar to select it (don’t forget this!). Then press Enter to make the changes and return to the main menu.

1-2 Main Menu.jpg


As a minimum, you need to configure the following menu entries:

  • Source Press the down arrow once and then Enter to select the “Source” menu and select the input you are using.

3-2 Source Menu.jpg


  • Output Select the “Output” menu and configure the following options.

3-3 Output Menu.jpg

  • Output Symbol Rate. Select the “Output” menu and then Symbol Rate. Enter the symbol rate in KS/s. Some sources and output modes do not work at high symbol rate – this is one of the first parameters to change if you are having problems, particularly in QPSKRF or "ugly" mode.
  • Output FEC. The default FEC is 7/8 – you can change this is if you want.
  • Output Mode. Again select the desired option using the space bar. Currently, only IQ (using the default pin selections for the BATC Portsdown modulator and filter board) and QPSKRF at an RF gain of 7 (for testing with an “ugly” signal directly from pin 32) are actively supported.
  • Output PID. Set the PID PMT to 255. This will ensure that the video PID is 256 – the BATC standard.
  • Output Frequency. Set the output frequency for your ADF4351 synthesizer here. If you are using QPSKRF “ugly” mode, set 437 MHz only.

Once you have set the output parameters, go back to the main menu.

1-2 Main Menu.jpg

Now you must configure the following:

  • Station. In the station menu, you can set your call and locator. The callsign is used to identify the digital transmission, and the callsign and locator are used in the test card overlay.
  • System Setup. It is important that you set your display type first here, so select Display. If you want to use the Waveshare touchscreen to control the Portsdown, select it with the spacebar and press enter. Note - if you want to continue to use the console mode, make sure that Console is selected.
  • System Setup Autostart. After you have selected the display type, you can select how you want your RPi to start up.

The first 4 options require you to log-in using a console before anything happens, whereas the last 3 do not require a console. TX_boot starts transmitting at power-on, so does not even require a touchscreen.

If you want to only use the touchscreen display select Display_boot and the system will always start up using the touchscreen only.

  • System Setup Additions. It is hoped to add other options in the System Setup menu as the software is developed.
  • Language. The menu language can be changed to French (or back to English) from this menu.


Your Portsdown transmitter is now set up and ready for use but will require a reboot for the configuration to take effect so go into the Shutdown menu and select Reboot. The Portsdown will now restart in whichever mode you set in the System Setup Autostart menu. Please refer to the appropriate section of the Portsdown Transmitter user guide for console or touch screen operation.