Difference between revisions of "Minitiouner Hardware"

From BATC Wiki
Jump to navigation Jump to search
 
(71 intermediate revisions by 2 users not shown)
Line 1: Line 1:
[[File:IMAG0218.jpg|400px]]
 
  
The MiniTiouner, developed and designed by Jean-Pierre F6DZP, is a DVB-S/S2 USB receiver card and a measurement tool that works with the software "Minitioune".
+
The MiniTiouner hardware, designed by Jean-Pierre F6DZP, is a DVB-S/S2 USB receiver card and measurement tool that works with the software "Minitioune".
  
 
Original schematics are here : http://www.vivadatv.org/viewtopic.php?f=80&t=366
 
Original schematics are here : http://www.vivadatv.org/viewtopic.php?f=80&t=366
  
[[File:Schema Minitiouner Sharp_.jpg|400px]]
+
There are several versions of the MiniTiouner hardware, all of which use the same MiniTiouner software and have very similar functionality.  This page describes the 2 versions sold by the BATC:
  
====BATC PCB====
+
* Version 1 sold by BATC available up to February 2017
  
Brian G4EWJ has designed a PCB for the BATC to enable easy home construction of the MiniTiouner hardware - components for over 200 units have been sold around the world.
+
* Version 2 sold by BATC and is the current version described on this page.  Sold as an easy to build home construction project with options to add an LCD display and simultaneously decode a 2nd channel.
  
All the project documentation is available for download in the zip file:
+
'''MiniTiouner-Pro''' is sold by the French Amateur Radio organisation REF as a completed unit to it's members and does have LCD and dual stream receiver possibility
  
[[:File:MTK1 Instructions v1-9, Parts v5, Overlay, Schematic v1.zip]]
+
'''MiniTioune-Express''' is sold by the DATVexpress team as a ready built unit. It does not have the option for LCD or 2nd channel decode. 
  
Colin G4KLB has done an excellent video on constructing the MiniTiouner:
+
The BATC Minitiouner hardware is designed for home construction and consists of the 3 main components described on this wiki page.
  
https://www.youtube.com/watch?v=vXUIQPeslwM
+
===How do I get started?===
  
When you have built your MiniTiouner, you can check it using the software "TestMyMiniTiouner" included in the Minitioune software package.
+
To build the unit you need to buy the following from the [https://batc.org.uk/shop/minitiouner MiniTiouner category in the BATC shop]
  
===Compatible NIM types===
+
*The ready programmed USB interface.
  
Only NIMs ( Network Interface Module) or tuners that have the following STMicroelectronics chips can be used:
+
*The version 2 main PCB.
  
*Zero tuner chip can be STB6100, STV6110, STV6111, STV6120
+
*The Serit tuner covering 143 - 2450 MHz
*Demodulator chip STV0903, STV0913, STV0910
 
  
The following NIMs can be used:
+
*The hard to find MCP1826 1v regulator.
* Eardatek EDS-4B47FF1B+ (sold by BATC shop during 2015 / 16)
+
 
* Sharp F7VZ0169 (sold by BATC shop during 2016)
+
All other components such as Rs and Cs are available from normal suppliers and the 5v switched regulator module is available from ebay.
* Samsung DNBU10711IST
+
 
* Samsung DNBU10512IST
+
A parts list for the version 2 PCB is available on the [[MiniTiouner hardware Version 2|V2 wiki page]] and can be used to order all other parts directly from Digikey.
* LG TDQX-S001F
+
 
* Serit SP2246
+
Total project cost using new parts and including a nice Hammond enclosure is around £85.
* Serit FTS-4335 (Sold by BATC shop in 2017)
+
 
Note - the NIM Serit FTS-4335 has a different pins configuration (40pins, not 26 pins) , so an adapter for "old pcbs" has been designed by Brian G4EWJ
+
'''New builders should go to this [[MiniTiouner hardware Version 2]] wiki page for more details, part list and construction tips.'''
 +
 
 +
===MiniTiouner main PCB===
 +
There are 2 variants of the MiniTiouner main PCB which contains the power supply components for the 5, 3.3 and 1 volt rails.
 +
 
 +
====Version 2 - April 2017 onwards====
 +
 
 +
As from April 2017 ONLY the version 2 PCB designed by Mike G0MJW is available from the BATC - new builders should use this version which takes the wide coverage Serit Tuner enabling coverage from 140 - 2500 MHz without any external upconverters.
 +
 
 +
[[File:serit in box2.jpg|400px]]
 +
 
 +
====Version 1 - before Feb 2017====
 +
 
 +
Version 1 was the original PCB designed by Brian G4EWJ and sold in the BATC shop until early 2017 - this board is no longer available and new builders should only read the [[MiniTiouner hardware Version 2|version 2 build documentation]].
 +
 
 +
[[File:IMAG0218.jpg|300px]]
 +
 
 +
See this [[MiniTiouner hardware Version 1]] wiki page for details.
 +
 
 +
===USB module===
 +
The MiniTioune receive hardware is connected to a Windows PC running the MinITiouner software over a standard USB 2.0 port.
 +
 
 +
[[File:usb.png|200px]]
 +
 
 +
The pre-programmed USB module available from the BATC shop acts as a 2 channel USB converter between the PC USB port and the NIM.  One channel is used for control and monitoring and the other carries the Transport stream data from the NIM.
 +
 
 +
If you buy a USB module from another source (not the BATC Shop) and need to program it, the instructions are here http://www.vivadatv.org/viewtopic.php?f=80&t=379.
 +
 
 +
Note - some people have noticed what appears to be a solder short between 2 pins on the IC on the USB module - see below - this is perfectly normal.
 +
 
 +
[[File:usb solder short.JPG|300px]]
 +
 
 +
===The NIM===
 +
 
 +
The NIM or Network interface module is the little metal box found inside Satellite Receivers (also called the tuner) and typically contains 2 chips : the Zero Tuner and the Demodulator. RF Signal is sent to the antenna connector "RF input", it is amplified by a transistor "booster", the zero tuner selects the frequency asked and the demodulator extracts the data (Transport Stream) that goes outside the NIM on a digital parallel output.
 +
 
 +
[[File:NIM open info .jpg|inside a NIM|300px]]
 +
 
 +
 
 +
The BATC shop used to sell a Sharp and Eardetek NIM with frequency coverage from 650 MHz through to 2600 MHz and so need an upconverter to receive 146 and 437 MHz.  As of February 2017 the Sharp and Samsung tuners are no longer available and the project now uses a NIM tuner from [[Serit tuner|Serit]] which covers from 143.75 MHz right through to 2450 MHz without the need for any upconverters. 
 +
 
 +
This extended frequency coverage gives greater flexibility and means up converters from the VHF and UHF bands are not required and enables the 10 GHz band, including Es'HailSat-2 down link, to be received on a standard domestic PLL LNB.  This makes building a receiver for 146 or 437 much easier, although you will need a pre-amp followed by lots of filtering for each band - take a look at the [[Filters|picture on this page]] if you want to know why!
 +
 
 +
However, due to a different pinouts from the Sharp NIM, the Serit NIM tuner will also need a simple adapter board to enable it to be plugged in to the Version 1 MiniTiouner hardware - Brian G4EWJ has designed a board and these are available from the BATC shop.  The adapter board and the Serit FTS4335 NIM tuner [https://batc.org.uk/shop/minitiouner are available from the BATC shop]. 
 +
 
 +
[[serit tuner| Full details of this board and using the tuner are available here.]]
 +
 
 +
Note: You only require the adaptor PCB if you are upgrading existing MiniTiouner hardware to include the Serit tuner.  [[Serit tuner|Check this page]] to work out if you should upgrade.
 +
 
 +
===Fitting a lock detector===
 +
 
 +
When Minitiouner is used at repeater site a lock detector is required to tell the repeater logic when a signal is being received.  Several designs based around the NE567 have been used but the simplest and most reliable is from Robin, G8DRK.
 +
 
 +
The 22kHz from the tuner is coming from a 3.3V port which is normally zero volts. When it outputs the 22kHz tone it does it by pulsing up to +3.3 volts with a 50% duty cycle. So we can simply smooth that and get about 1.6 volts - more than enough to turn a transistor on. 
 +
 
 +
This circuit should drive most small 12 volt "signal" relays. If relay needs more than 90mA consider using a smaller one or try a beefier transistor but with a gain of at least 100.
 +
 
 +
[[File:TT lock 1.jpg|400px]]
 +
 
 +
This following circuit provides a 5-volt TTL output when the 22 kHz tone is present:
 +
 
 +
[[File:TT lock 2.jpg|400px]]
 +
 
 +
In both circuits the green LED functions as a Lock-LED, as long as you set "22kHz_switch=2" in the MiniTioune.ini file.

Latest revision as of 11:08, 17 April 2018

The MiniTiouner hardware, designed by Jean-Pierre F6DZP, is a DVB-S/S2 USB receiver card and measurement tool that works with the software "Minitioune".

Original schematics are here : http://www.vivadatv.org/viewtopic.php?f=80&t=366

There are several versions of the MiniTiouner hardware, all of which use the same MiniTiouner software and have very similar functionality. This page describes the 2 versions sold by the BATC:

  • Version 1 sold by BATC available up to February 2017
  • Version 2 sold by BATC and is the current version described on this page. Sold as an easy to build home construction project with options to add an LCD display and simultaneously decode a 2nd channel.
MiniTiouner-Pro is sold by the French Amateur Radio organisation REF as a completed unit to it's members and does have LCD and dual stream receiver possibility
MiniTioune-Express is sold by the DATVexpress team as a ready built unit. It does not have the option for LCD or 2nd channel decode.  

The BATC Minitiouner hardware is designed for home construction and consists of the 3 main components described on this wiki page.

How do I get started?

To build the unit you need to buy the following from the MiniTiouner category in the BATC shop

  • The ready programmed USB interface.
  • The version 2 main PCB.
  • The Serit tuner covering 143 - 2450 MHz
  • The hard to find MCP1826 1v regulator.

All other components such as Rs and Cs are available from normal suppliers and the 5v switched regulator module is available from ebay.

A parts list for the version 2 PCB is available on the V2 wiki page and can be used to order all other parts directly from Digikey.

Total project cost using new parts and including a nice Hammond enclosure is around £85.

New builders should go to this MiniTiouner hardware Version 2 wiki page for more details, part list and construction tips.

MiniTiouner main PCB

There are 2 variants of the MiniTiouner main PCB which contains the power supply components for the 5, 3.3 and 1 volt rails.

Version 2 - April 2017 onwards

As from April 2017 ONLY the version 2 PCB designed by Mike G0MJW is available from the BATC - new builders should use this version which takes the wide coverage Serit Tuner enabling coverage from 140 - 2500 MHz without any external upconverters.

Serit in box2.jpg

Version 1 - before Feb 2017

Version 1 was the original PCB designed by Brian G4EWJ and sold in the BATC shop until early 2017 - this board is no longer available and new builders should only read the version 2 build documentation.

IMAG0218.jpg

See this MiniTiouner hardware Version 1 wiki page for details.

USB module

The MiniTioune receive hardware is connected to a Windows PC running the MinITiouner software over a standard USB 2.0 port.

Usb.png

The pre-programmed USB module available from the BATC shop acts as a 2 channel USB converter between the PC USB port and the NIM. One channel is used for control and monitoring and the other carries the Transport stream data from the NIM.

If you buy a USB module from another source (not the BATC Shop) and need to program it, the instructions are here http://www.vivadatv.org/viewtopic.php?f=80&t=379.

Note - some people have noticed what appears to be a solder short between 2 pins on the IC on the USB module - see below - this is perfectly normal.

Usb solder short.JPG

The NIM

The NIM or Network interface module is the little metal box found inside Satellite Receivers (also called the tuner) and typically contains 2 chips : the Zero Tuner and the Demodulator. RF Signal is sent to the antenna connector "RF input", it is amplified by a transistor "booster", the zero tuner selects the frequency asked and the demodulator extracts the data (Transport Stream) that goes outside the NIM on a digital parallel output.

inside a NIM


The BATC shop used to sell a Sharp and Eardetek NIM with frequency coverage from 650 MHz through to 2600 MHz and so need an upconverter to receive 146 and 437 MHz. As of February 2017 the Sharp and Samsung tuners are no longer available and the project now uses a NIM tuner from Serit which covers from 143.75 MHz right through to 2450 MHz without the need for any upconverters.

This extended frequency coverage gives greater flexibility and means up converters from the VHF and UHF bands are not required and enables the 10 GHz band, including Es'HailSat-2 down link, to be received on a standard domestic PLL LNB. This makes building a receiver for 146 or 437 much easier, although you will need a pre-amp followed by lots of filtering for each band - take a look at the picture on this page if you want to know why!

However, due to a different pinouts from the Sharp NIM, the Serit NIM tuner will also need a simple adapter board to enable it to be plugged in to the Version 1 MiniTiouner hardware - Brian G4EWJ has designed a board and these are available from the BATC shop. The adapter board and the Serit FTS4335 NIM tuner are available from the BATC shop.

Full details of this board and using the tuner are available here.

Note: You only require the adaptor PCB if you are upgrading existing MiniTiouner hardware to include the Serit tuner.  Check this page to work out if you should upgrade.

Fitting a lock detector

When Minitiouner is used at repeater site a lock detector is required to tell the repeater logic when a signal is being received. Several designs based around the NE567 have been used but the simplest and most reliable is from Robin, G8DRK.

The 22kHz from the tuner is coming from a 3.3V port which is normally zero volts. When it outputs the 22kHz tone it does it by pulsing up to +3.3 volts with a 50% duty cycle. So we can simply smooth that and get about 1.6 volts - more than enough to turn a transistor on.

This circuit should drive most small 12 volt "signal" relays. If relay needs more than 90mA consider using a smaller one or try a beefier transistor but with a gain of at least 100.

TT lock 1.jpg

This following circuit provides a 5-volt TTL output when the 22 kHz tone is present:

TT lock 2.jpg

In both circuits the green LED functions as a Lock-LED, as long as you set "22kHz_switch=2" in the MiniTioune.ini file.