Difference between revisions of "Repeater system full quad view IR configuration"

From BATC Wiki
Jump to navigation Jump to search
 
(One intermediate revision by one other user not shown)
Line 20: Line 20:
 
Substitute the codes for your HDMI switch if they are different.  In the file that follows, note that IR codes of the form "2nec:0x17" first send the code for the upstream IR switch (in this case nec0x17), and then send the code to the downstream switch (in this case nec:0x12 which is set in the output2ndhdmicode=nec:0x12 parameter).
 
Substitute the codes for your HDMI switch if they are different.  In the file that follows, note that IR codes of the form "2nec:0x17" first send the code for the upstream IR switch (in this case nec0x17), and then send the code to the downstream switch (in this case nec:0x12 which is set in the output2ndhdmicode=nec:0x12 parameter).
  
[[File:HDMIquad (Medium).JPG|400px]]
+
[[File:HDMIquad (Medium).JPG|600px]]
  
 
Fragment of Config file:
 
Fragment of Config file:
Line 41: Line 41:
 
  showquadformultipleinputs=yes
 
  showquadformultipleinputs=yes
 
  cascadedswitches=yes
 
  cascadedswitches=yes
 
+
 
  outputswitchcontrol=ir
 
  outputswitchcontrol=ir
 
  showoutputongpio=yes
 
  showoutputongpio=yes

Latest revision as of 16:43, 22 February 2022

Back to repeater controller main page

The section of the config file for basic IR configuration is shown here for an HDMI switch with the following control codes:

Function IR Code
Input 1 0x17
Input 2 0x12
Input3 0x59
Input 4 0x08
Quad 0x18

Substitute the codes for your HDMI switch if they are different. In the file that follows, note that IR codes of the form "2nec:0x17" first send the code for the upstream IR switch (in this case nec0x17), and then send the code to the downstream switch (in this case nec:0x12 which is set in the output2ndhdmicode=nec:0x12 parameter).

HDMIquad (Medium).JPG

Fragment of Config file:

# Input config
# Recommended gpio pins for "input active" are 32, 35, 18, 22, 16, 19 and 21

# announcemediatype determines the player used

# Switcher can use "ir" or "gpio" or "i2c"
# IR uses a TX on GPIO pin 12
# GPIO uses pins 36, 37, 38, 33, 31, 29, 23, 24.  Can be enabled with ir or i2c
# i2c uses FMS6501A on Output channel 1
# activeinputhold (yes/no) means that lower priority inputs do not get replaced by higher priority (except pri 1)
# Show Quad is yes/no and overides activeinputhold

# Number of available inputs does not include the controller, so is max 6
availableinputs=6
activeinputhold=no
showquadformultipleinputs=yes
cascadedswitches=yes

outputswitchcontrol=ir
showoutputongpio=yes
outputhdmiresetcode=nec:0x17
output2ndhdmicode=nec:0x12
outputhdmiquadcode=2nec:0x18
outputi2caddress=3
outputi2cquadchannel=9

input0name=Controller
output0code=nec:0x17
output0hdmiswitchpin=36
output0i2cchannel=1
output0audioi2cbit=0

input1name=70cms Ryde
input1prioritylevel=1
input1activegpiopin=32
output1code=2nec:0x17
output1hdmiswitchpin=37
output1i2cchannel=2
output1audioi2cbit=1
input1announcemediatype=jpg
input1announcemediafile=/home/pi/tmp/input1.jpg
input1announcemediaduration=3

input2name=23cms Ryde
input2prioritylevel=2
input2activegpiopin=35
output2code=2nec:0x12
output2hdmiswitchpin=38
output2i2cchannel=3
output2audioi2cbit=2
input2announcemediatype=jpg
input2announcemediafile=/home/pi/tmp/input2.jpg
input2announcemediaduration=3

input3name=Stream rxr
input3prioritylevel=3
input3activegpiopin=18
output3code=2nec:0x59
output3hdmiswitchpin=33
output3i2cchannel=4
output3audioi2cbit=3
input3announcemediatype=jpg
input3announcemediafile=/home/pi/tmp/input3.jpg
input3announcemediaduration=3

input4name=Analogue Rxr
input4prioritylevel=7
input4activegpiopin=22
output4code=2nec:0x08
output4hdmiswitchpin=31
output4i2cchannel=5
output4audioi2cbit=4
input4announcemediatype=jpg
input4announcemediafile=/home/pi/tmp/input4.jpg
input4announcemediaduration=3

input5name=Spare 1
input5prioritylevel=7
input5activegpiopin=16
output5code=nec:0x59
output5hdmiswitchpin=29
output5i2cchannel=6
output5audioi2cbit=5
input5announcemediatype=jpg
input5announcemediafile=/home/pi/tmp/input5.jpg
input5announcemediaduration=10

input6name=Spare 2
input6prioritylevel=8
input6activegpiopin=19
output6code=nec:0x08
output6hdmiswitchpin=23
output6i2cchannel=7
output6audioi2cbit=6
input6announcemediatype=jpg
input6announcemediafile=/home/pi/tmp/input6.jpg
input6announcemediaduration=3

If it is desired to have the quad available as a source in the carousel, then the availableinputs= could be increased from 6 to 7, and the following code added to make the quad a source that is then selectable in the carousel:

input7name=Quad
input7prioritylevel=8
input7activegpiopin=21
output7code=2nec:0x18
output7hdmiswitchpin=24
output7i2cchannel=8
output7audioi2cbit=7
input7announcemediatype=jpg
input7announcemediafile=/home/pi/tmp/input7.jpg
input7announcemediaduration=3