Difference between revisions of "The Portsdown DATV transceiver system"

From BATC Wiki
Jump to navigation Jump to search
Line 10: Line 10:
 
The project involves some basic construction and is based around a Raspberry Pi with a touchscreen, an external local oscillator and a filter modulator card available from the BATC shop - outline specifications are as follows:
 
The project involves some basic construction and is based around a Raspberry Pi with a touchscreen, an external local oscillator and a filter modulator card available from the BATC shop - outline specifications are as follows:
  
• Frequency coverage of the 146 MHz, 437 MHz and 23cms ATV bands
+
• Frequency coverage of the 71, 146 MHz, 437 MHz and 23cms ATV bands
  
 
• MPEG-2 and MPEG-4 (H264) video encoding
 
• MPEG-2 and MPEG-4 (H264) video encoding

Revision as of 17:06, 6 April 2017

Portsdown with Menu 1.jpg

Introduction

The Portsdown DATV transmitter project provides an easy way to “get on air” with Digital ATV at a relatively low cost covering all of the commonly used DATV modes enabling it to be used for cross town QSOs, accessing ATV repeaters and for working the DX using Reduced bandwidth (RB-TV) modes.

The aim of the project is to enable an amateur radio operator with little or no knowledge of Digital ATV to construct the hardware elements, load and configure the software and use the system to send live Digital ATV signals across town on his existing aerials. 

The project involves some basic construction and is based around a Raspberry Pi with a touchscreen, an external local oscillator and a filter modulator card available from the BATC shop - outline specifications are as follows:

• Frequency coverage of the 71, 146 MHz, 437 MHz and 23cms ATV bands

• MPEG-2 and MPEG-4 (H264) video encoding

• Cost-effective stand-alone (not PC based) Digital TV Transmit solution

• Wide range of Symbol rates from 125 Ks to 4Ms including Reduced Bandwidth (RB-TV) modes and “normal” DATV modes

• Analogue video input to allow use of camcorders and mixing desks

• Use of commonly available components and modules

• Modular construction enabling a step-by-step system build and easy trouble shooting

• Designed to encourage home construction and requiring an average skill level

• Fully documented and supported including easy software installation and upgrades

Note - the Portsdown project has evolved since the original articles were written and now defines just the Raspberry Pi based transmitter - there is no Portsdown receiver project although it is possible to add an RTL dongle based monitoring receiver.  The MiniTioune USB receiver project is the recommended receive solution for all DATV transmissions including the Portsdown transmitter. 

System overview

At the heart of the The Portsdown Transmitter is a Raspberry Pi (RPi) computer running a BATC customised version of the F5OEO rpidatv software. The choice of the RPi is primarily due to the fact that it has an on-board MPEG-4 (H264) encoder and the versatile hardware interface (GPIO) capabilities. 1-1 Block Diagram.jpg

Touch screen control

A touch screen interface (available from Amazon) enables the system to be used as a standalone unit without further need to connect up keyboard and mouse. If the LCD is not available, the system can be controlled by using an external PC connected over a wired or wi-fi network (console mode).


1-3 LCD Menu.jpg

Modulator and Filter board

The output from the Rpi is connected to the Filter Modulator board (the only custom piece of hardware - Blank PCBs and fully assembled boards are available from the BATC shop).

This board also requires an on frequency local oscillator signal and the Portsdown transmitter software has been designed to control an ADF4351 chip (available from ebay) to give an output on 146, 437 and 23cms.

Audio and video inputs

The Portsdown transmitter will take audio and video inputs from the Rpi camera, an Easycap USB dongle and a USB sound card / dongle - all these are readily available from ebay and Amazon.

Next steps?

The great thing is you don't have to build any hardware to get started and send pictures across the shack!!

Now you've read the system overview, take a look at the user guide - it contains a lot more information on what hardware is required and where to buy it and how to get and configure the software.

Or if you want to print off an overview of the project, we've produced a 2 page introductory brochure which also includes a spec sheet for the Portsdown transmitter.