Difference between revisions of "The Portsdown DATV transceiver system"

From BATC Wiki
Jump to navigation Jump to search
Line 14: Line 14:
  
 
* [http://www.batc.org.uk/forum/viewforum.php?f=103&sid=fc79811b4d99a7795a433fd5c079e20d BATC members forum pages]
 
* [http://www.batc.org.uk/forum/viewforum.php?f=103&sid=fc79811b4d99a7795a433fd5c079e20d BATC members forum pages]
'''Important note - the Portsdown transmitter has been designed to "work out of the box":
 
*You do not need to do anything other than follow the [[Initial setup|initial set up guide]]
 
*Do not load any device drivers
 
*Do not tinker with Linux commands
 
 
If you do, we don't have time to support you and will just advise you to reformat your SD card and start again!'''
 
---------------------------
 
 
  
 
===Introduction===
 
===Introduction===

Revision as of 09:00, 8 January 2017

This page is designed to give an brief overview of the Portsdown transmitter project - for more details see the user guide.

There's also a "where do I begin" guide

And of course an FAQ

And for interactive discussion with other constructors see the BATC members forum:

Introduction

The Portsdown DATV transmitter project provides an easy way to “get on air” with Digital ATV at a relatively low cost, covers most of the common modes and involves some basic construction.

• Symbol rates to include the Reduced Bandwidth (RB-TV) modes and “normal” DATV modes

• Frequency coverage of 146 MHz, 437 Mhz and 23cms

• Cost-effective stand-alone (not PC based) Digital TV Transmit solution

• Analogue video input to allow use of camcorders and mixing desks

• Use of commonly available components and modules

• Modular construction enabling a step-by-step system build and easy trouble shooting

• Designed to encourage home construction and requiring an average skill level

• Fully documented and supported including easy software installation and upgrades


The aim is to enable an amateur operator with little or no knowledge of Digital ATV to construct the hardware elements, load and configure the software and use the system to send live Digital ATV signals across town on his existing aerials. It will include the new DX RB-TV modes and the ability to receive and transmit to local repeaters using the more traditional 2 and 4 Msymbol DATV modes.

System overview

At the heart of the Portsdown project transmitter is a Raspberry Pi (RPi) computer running a BATC customised version of the F5OEO rpidatv software. The choice of the RPi is primarily due to the fact that it has an on-board MPEG-4 (H264) encoder and the versatile hardware interface (GPIO) capabilities. 1-1 Block Diagram.jpg

Touch screen control

A touch screen interface (available from Amazon) on the RPi enables the system to be used without further need to connect up keyboard and mouse. If the LCD is not available, the system can be controlled by using an external PC connected over a wired or wi-fi network (console mode).


1-3 LCD Menu.jpg

Modulator and Filter board

The output from the Rpi is connected to the Filter Modulator board (the only custom piece of hardware - PCBs will be available from the BATC shop).

This board also requires an on frequency local oscillator signal and the Portsdown transmitter software has been designed to control an ADF4351 chip (available from ebay) to give an output on 146, 437 and 23cms.

Audio and video inputs

The Portsdown transmitter will take audio and video inputs from the Rpi camera, an Easycap USB dongle and a USB sound card / dongle - all these are readily available from ebay and Amazon.

Next steps?

The great thing is you don't have to build any hardware to get started and send pictures across the shack!!

Now you've read the system overview, take a look at the user guide - it contains a lot more information on the hardware required and loading the software and includes a "where do I begin" section..