Portsdown 4

The Portsdown 4 system has been specifically designed to be used with the Raspberry Pi 4 and the official Raspberry Pi 7 inch touchscreen. It will drive a Pluto SDR or the LimeSDR and the DATV Express board (DVB-S only).

Portsdown 4 is the simplest and easiest to construct, with a barebones system consisting of:

Raspberry Pi4 2GB model
7" touch screen
8, 16 or 32 GB SD card
Adalm Pluto or Lime SDRmini

This will give you a basic DATV transmit system from 30 to 3500 MHz when using a Lime SDR and 50MHz to 4100 MHz with the Pluto.

With the addition of a MiniTiouner USB receiver [[1]], you will have a full spec DVB-S/S2 DATV transceiver. DVB-T transmit capability is now included, and the Knucker Tuner can be used with Portsdown 4 for DVB-T receive.

Capabilities

The Portsdown 4 has the following transmit and receive capabilities:

DVB-S, DVB-S2 and DVB-T (H264 only) transmissions from a Pluto SDR connected by USB
DVB-S, DVB-S2 and DVB-T (MPEG-2 and H264) transmissions from a LimeSDR Mini or LimeSDR USB
DVB-S (MPEG-2 and H264) transmissions from a DATV Express Board connected by USB
Supported transmit video sources include the Raspberry Pi Camera, C920 WebCam or a USB-connected EasyCap composite video capture device
Streaming to the BATC Streamer using the Raspberry Pi Camera or EasyCap composite video capture device as a source
Display of streams from the BATC Streamer

When a MiniTiouner USB receiver is connected via USB:

Reception and display of DVB-S and DVB-S2 (MPEG-2, H264 and H265) signals

When a BATC Knucker USB tuner connected by USB:

Reception and display of DVB-T and DVB-T2 (MPEG-2, H264 and H265) signals

Portsdown test and alignment aids

Control of a Pluto, LimeSDR Mini, DATV Express, ADF4351, Elcom and SLO Microwave Source using the Portsdown 4 Signal Generator.

Basic spectrum display of band occupancy using the "Portsdown Band Viewer" - requires a LimeSDR Mini to be connected.

The Portsdown 4 does NOT support the BATC Filter-modulator board or Ugly mode.

Hardware

Full details of the Portsdown hardware are available here.

No other models of Raspberry Pi or touchscreen are planned to be supported in the near future.

Portsdown 4 GPIO connections

Due to a reassignment of the GPIO pins on Raspberry Pi4, the connections are different to previous generations of Portsdown.

The Portsdown 4 GPIO Connections are defined here: Portsdown 4 GPIO Connections.

Powering the Pluto

The Raspberry Pi 4 has increased power capabilities on its USB ports, and the Pluto does not work well with USB Hubs, so it is recommended that you connect the Pluto directly to a USB3 port (the blue ones) on the Raspberry Pi 4. Do not use a USB hub or power the Pluto from its USB power port.

Software

The Portsdown 4 software is available on a pre-programmed SD card from the BATC shop https://batc.org.uk/shop/portsdown-transmitter-pre-programmed-sd-card/

If you wish to build your own card the build is on GitHub at https://github.com/BritishAmateurTelevisionClub/portsdown4

You MUST start with a fresh build of Raspios Buster Lite (NOT the older Raspbian) on an SD Card of 8 GB or greater, so you will need to rebuild any previous Langstone or Portsdown A27 card.

Langstone Microwave transceiver

The Portsdown 4 software build is also compatible with the Langstone Microwave transceiver software, which can be loaded from touchscreen selections (menu 2) AFTER the Portsdown software has been installed.

See https://wiki.microwavers.org.uk/Langstone_Project for more details and the full spec of the Langstone.

To operate, the Langstone software needs a Pluto to be connected by USB, and a compatible USB Audio dongle.

Pluto Capabilities

The Portsdown 4 support for the Pluto SDR is experimental at the moment and it has limited functionality as described here Portsdown 4 Pluto.

FAQ

Is it possible to rotate the PiCam image in software as it is on it's side?

No - you need to do the camera mounting modification which Colin G4KLB described in CQ-TV 267

Can I upgrade from Langstone or a previous version incluing Portsdown A27?

No - you must start with a clean image on your SD card

When I try to update I get the error "Unable to contact GitHub for update, Internet connection to Google seems OK". The solution is to log in by ssh and run the following commands:

cd /home/pi
wget https://raw.githubusercontent.com/BritishAmateurTelevisionClub/portsdown4/master/update.sh  -O /home/pi/update.sh
chmod +x /home/pi/update.sh
./update.sh

I have built my Portsdown 4 but the screen is upside down. How can I get it the right way up?

Menu 3, System Config, Invert 7 inch

More information

For more information see https://forum.batc.org.uk/viewtopic.php?f=103&t=6804